# CBNA-200-Z4

CBNA-200-Z4

# Features

  • Combined power supply with DMX driver, 4 outputs, total 200 Watts.

  • USITT DMX 512 Standard Protocol to work with Orbit TP or other DMX controllers.

  • Three Multi-Segment displays for easy operation.

  • 20 fixed colors and 9 programmed color changing and fade time effects.

  • 3-Pin terminal block for DMX offers easy wiring and installation.

  • Wall mountable.

The CBNA-200-Z4 has 4 RJ-45 36W-48VDC ports. Multiple, identical luminaires may be daisy chained together and attached to a single port. We cannot address each individual luminaire, but instead address each port on the CBNA-200-Z4. Do not mix different wattage LED fixtures on same port.

Warning

DO NOT EXCEED 36 WATTS PER PORT/OUTPUT

AN RJ45 TERMINATOR IS NEEDED AT THE END OF EACH LINE TO ENABLE A DC LOOP

# Stand Alone User Guide

Menu

# 1. Turn power ON / OFF

The CBNA-200-Z4 has no switch, simply plug it into a power outlet.

# 2. Preset Colors

There are 20 built-in preset colors in the device. Press Menu, the display will show “C01” on the display.

Press Up or Down to select the desired color from C01 ~ C20.

Press Menu to select/confirm.

Note

Is will not be in effect once the driver receives a DMX signal.

MODE R G B
C01 100 0 0
C02 100 0 100
C03 100 0 50
C04 50 0 100
C05 100 0 20
C06 100 15 100
C07 100 15 50
C08 50 15 50
C09 0 0 100
C10 0 40 100
C11 0 15 100
C12 0 100 60
C13 0 100 30
C14 100 100 30
C15 0 60 100
C16 0 100 0
C17 100 80 0
C18 50 100 0
C19 100 15 0
C20 100 100 100

# 3. Fade transitions (9 programs)

  • There are 9 built-in programs in the device.

  • Press Menu, the display will show “F01”.

  • Press Up or Down to select desired transition program from F01 ~ F09

  • The fade time of the transition can be changed from 1 to 20 secondes. Eg: F03 is running, the fade time can be changed by pressing menu and holding for 3 seconds.

  • The display will show 2 digits.

  • The fade time can be adjusted from 1 to 20 by pressing Up or Down, and confirmed by pressing Menu.

# 4. DMX Address Setting

  • Press Menu and the display will show the initial DMX address “001”.

  • The user can select the desired address from 001 ~ 511 by pressing Up or Down.

  • Press Menu to confirm.

  • First address should be 011 and each CBNA-200-Z4 needs 20 channels (in 5channels/full DMX mode), second unit address should be set at 031.

  • DMX address “512” is test mode.

# 5. DMX mode setting

  • The following mode can be selected by pressing Menu to confirm it.

  • Press Menu first and the display shows “S--” and press Up or Down to select the desired program from S01~S21. Press Menu to confirm.

  • For maximum flexibility, you should turn on the following modes: S11, S20, S31, S40.

SETTINGS MODE
S10 Control all the LED fixtures in the same mode (default)
S11 Control each port (x4) independently
S20 Master off (default)
S21 Master on
S30 RGB 3 channels (default)
S31 RGB, Dimmer, Strobe 5 channels
S40 Delay off (default)
S41 Delay on

# 6. Signal indicator

The green LED light shows up when the driver is receiving DMX signal.

# 7. Sleep Mode

  • After 1 minute without instruction from the keypad, the control unit will automatically go into Sleep Mode. In Sleep Mode, the control unit is functional but the display is off and the keypad is locked.

  • To exit Sleep Mode, the user can press the Menu button and hold for 5 seconds until the display turns on. When using the DMX Address to control the lighting fixtures, Sleep Mode will trigger after 30 seconds.

# DMX Channels

CBNA-200 Channel 3 CH Mode 5 CH Mode (Default)
CH 1 Port 1 R Port 1 R
CH 2 G G
CH 3 B B
CH 4 Port 2 R Dimmer
CH 5 G Strobe
CH 6 B Port 2 R
CH 7 Port 3 R G
CH 8 G B
CH 9 B Dimmer
CH 10 Port 4 R Strobe
CH 11 G Port 3 R
CH 12 B G
CH 13 N/A B
CH 14 Dimmer
CH 15 Strobe
CH 16 Port 4 R
CH 17 G
CH 18 B
CH 19 Dimmer
CH 20 Strobe
Last Updated: 8/5/2020, 3:33:50 PM