CBNA-200-Z4

CBNA-200-Z4

Features

  • Combined power supply with DMX driver, 4 outputs, total 200 Watts.

  • USITT DMX 512 Standard Protocol to work with Orbit TP or other DMX controllers.

  • Three Multi-Segment displays for easy operation.

  • 20 fixed colors and 9 programmed color changing and fade time effects.

  • 3-Pin terminal block for DMX offers easy wiring and installation.

  • Wall mountable.

The CBNA-200-Z4 has 4 RJ-45 36W-48VDC ports. Multiple, identical luminaires may be daisy chained together and attached to a single port. We cannot address each individual luminaire, but instead address each port on the CBNA-200-Z4. Do not mix different wattage LED fixtures on same port.

WARNING

DO NOT EXCEED 36 WATTS PER PORT/OUTPUT

AN RJ45 TERMINATOR IS NEEDED AT THE END OF EACH LINE TO ENABLE A DC LOOP

Stand Alone User Guide

Menu

1. Turn power ON / OFF

The CBNA-200-Z4 has no switch, simply plug it into a power outlet.

2. Preset Colors

There are 20 built-in preset colors in the device. Press Menu, the display will show “C01” on the display.

Press Up or Down to select the desired color from C01 ~ C20.

Press Menu to select/confirm.

Note

Is will not be in effect once the driver receives a DMX signal.

MODERGB
C0110000
C021000100
C03100050
C04500100
C05100020
C0610015100
C071001550
C08501550
C0900100
C10040100
C11015100
C12010060
C13010030
C1410010030
C15060100
C1601000
C17100800
C18501000
C19100150
C20100100100

3. Fade transitions (9 programs)

  • There are 9 built-in programs in the device.

  • Press Menu, the display will show “F01”.

  • Press Up or Down to select desired transition program from F01 ~ F09

  • The fade time of the transition can be changed from 1 to 20 secondes. Eg: F03 is running, the fade time can be changed by pressing menu and holding for 3 seconds.

  • The display will show 2 digits.

  • The fade time can be adjusted from 1 to 20 by pressing Up or Down, and confirmed by pressing Menu.

4. DMX Address Setting

  • Press Menu and the display will show the initial DMX address “001”.

  • The user can select the desired address from 001 ~ 511 by pressing Up or Down.

  • Press Menu to confirm.

  • First address should be 011 and each CBNA-200-Z4 needs 20 channels (in 5channels/full DMX mode), second unit address should be set at 031.

  • DMX address “512” is test mode.

5. DMX mode setting

  • The following mode can be selected by pressing Menu to confirm it.

  • Press Menu first and the display shows “S--” and press Up or Down to select the desired program from S01~S21. Press Menu to confirm.

  • For maximum flexibility, you should turn on the following modes: S11, S20, S31, S40.

SETTINGSMODE
S10Control all the LED fixtures in the same mode (default)
S11Control each port (x4) independently
S20Master off (default)
S21Master on
S30RGB 3 channels (default)
S31RGB, Dimmer, Strobe 5 channels
S40Delay off (default)
S41Delay on

6. Signal indicator

The green LED light shows up when the driver is receiving DMX signal.

7. Sleep Mode

  • After 1 minute without instruction from the keypad, the control unit will automatically go into Sleep Mode. In Sleep Mode, the control unit is functional but the display is off and the keypad is locked.

  • To exit Sleep Mode, the user can press the Menu button and hold for 5 seconds until the display turns on. When using the DMX Address to control the lighting fixtures, Sleep Mode will trigger after 30 seconds.

DMX Channels

CBNA-200 Channel3 CH Mode5 CH Mode (Default)
CH 1Port 1RPort 1R
CH 2GG
CH 3BB
CH 4Port 2RDimmer
CH 5GStrobe
CH 6BPort 2R
CH 7Port 3RG
CH 8GB
CH 9BDimmer
CH 10Port 4RStrobe
CH 11GPort 3R
CH 12BG
CH 13N/AB
CH 14Dimmer
CH 15Strobe
CH 16Port 4R
CH 17G
CH 18B
CH 19Dimmer
CH 20Strobe
Last Updated: 1/28/2019, 6:28:58 PM